An inexpensive UV-LED photoacoustic based real-time sensor-system detecting exhaled trace-acetone.

In this research we present a low-cost system for breath acetone analysis based on UV-LED photoacoustic spectroscopy. We considered the end-tidal phase of exhalation, which represents the systemic concentrations of volatile organic compounds (VOCs) - providing clinically relevant information about the human health. This is achieved via the development of a CO2-triggered breath sampling system, which collected alveolar breath over several minutes in sterile and inert containers. A real-time mass spectrometer is coupled to serve as a reference device for calibration measurements and subsequent breath analysis. The new sensor system provided a 3σ detection limit of 8.3 ppbV and an NNEA of 1.4E-9 Wcm-1Hz-0.5. In terms of the performed breath analysis measurements, 12 out of 13 fell within the error margin of the photoacoustic measurement system, demonstrating the reliability of the measurements in the field.

Impact of drought stress on vitamin C and anthocyanin content in cultivated lettuces (Lactuca sativa L.) and wild relatives (Lactuca spp.).

Introduction: Lettuce production and quality could be seriously affected by the increasingly limited water resources. Methods: The effect of drought on the content of two antioxidant compounds, vitamin C and anthocyanins, in five cultivated lettuces and two wild relatives was assessed for 2 years. Results and discusion: In leaf samples, Lactuca wild species generally had a higher content of total vitamin C than the cultivated lettuces. In contrast, the commercial varieties usually contained more total anthocyanins than the wild species. Total vitamin C decreased with the drought stress in all accessions, commercial varieties, and lettuce wild relatives, with this tendency being consistent and reproducible across the 2 years. These differences were significant in the case of the green commercial varieties 'Winter Crop' (in 2020/2021) and 'Dolomiti G12' (in 2021/2022) and very significant in the red commercial variety 'Red Sails' (in 2020/2021). However, the only group in which the effect of drought was either significant or very significant in both years was the wild species, Lactuca homblei and Lactuca dregeana, and in the latter also in both tissues (leaf and stem) analyzed. Water stress resulted in an increase of the total anthocyanin content in the leaves from all the accessions, both red commercial varieties and wild relatives, in both years. The most significant enrichment and the only one being either significant or very significant in both years was observed in one of the wild relatives assayed (L. homblei). Stems (L. dregeana) contained more anthocyanins than leaves under control conditions, and it was exactly the opposite under drought. Changes in anthocyanins in the two tissues in response to drought stress were in opposite directions, increasing in leaves and decreasing in stems. This could suggest a translocation of anthocyanins as a first quick mechanism to cope with a severe lack of water. In conclusion, anthocyanins (unlike vitamin C) could play a role in the mechanisms deployed by the plant to tolerate drought stress. The wild species with a robust significant enrichment in anthocyanins as a response to drought (L. homblei) is a promising plant material to breed more resilient lettuces.

Effect of Femtosecond Ultraviolet and Infrared Laser Wavelength on Plasma Characteristics of Metals, Ceramics and Glass Samples Using Femtosecond Laser-Induced Breakdown Spectroscopy.

In this work, we present studies on the effect of laser wavelengths on the laser-induced plasma characterization using a femtosecond (fs) ytterbium-doped potassium-gadolinium tungstate (Yb:KGW) laser. Plasma plumes of copper, steel, ceramics, and glass samples were induced using a multiple shot of 200 fs laser pulses with 1030 nm and 343 nm wavelengths at fixed laser fluence (10.5J/cm2) and analyzed using the laser-induced breakdown spectroscopy (LIBS) technique. Time-resolved fs-LIBS measurements were performed on the same set of samples and under the same experimental conditions. For the calculation of plasma parameters, the set of spectral lines of Cu(I) (for copper sample), Fe(I) (for steel sample), and Ca(I), K(I) (for glass and ceramics samples) were observed. The plasma electron temperature and density were evaluated from the Boltzmann plots and Stark-broadening profiles of the plasma spectral lines, assuming the local thermodynamic equilibrium condition. Time-resolved plasma temperature and electron density for fs-LIBS using ultraviolet (UV) and infrared (IR) laser wavelengths were analyzed and no significant dependence on fs laser wavelength was observed for any of the samples. However, for all samples the signal-to-noise ratio (SNR) significantly increased using UV laser radiation: copper (∼100%), steel (∼300%), glass (∼400%), and ceramics (∼40%). Therefore, by using a fs UV laser wavelength for laser-induced breakdown spectroscopy experiments, for certain materials the SNR and at the same time the limit of detection can be significantly enhanced.

Structural and thermoluminescence properties of lithium borate glass matrices under UV and beta radiation.

In the present work, glass samples in the (100 - x)B2O3-xLi2O binary system, with x varying from 30 to 50 mol%, were prepared using the conventional melting and moulding method, with the main objective of evaluating the thermoluminescence response when exposing these materials to ultraviolet (UV) radiation. Complementary analysis based on density, optical absorption on the UV-visible region (UV-vis absorbance), Fourier transform infrared spectroscopy on the medium region, X-ray diffraction, and differential thermal analysis measurements were performed. Thermoluminescence measurements of vitreous samples showed glow curves with at least one peak with a maximum temperature of ~170°C after exposure to UV radiation in the temperature range 50-250°C. Samples were also exposed to beta radiation in the temperature range 25-275°C, also showing single peaks with a maximum temperature of ~150°C.

Is beauty worth the risk? Self-confidence is the key motivating factor driving tanning bed use among undergraduate students at South Dakota universities.

Background: Exposure to ultraviolet radiation is a leading risk factor for developing all types of skin cancer. In the United States, an estimated 7.8 million young adults engage in indoor tanning. Objective: Here, it is hypothesized that certain populations of students at undergraduate universities, namely sorority members, have a greater frequency of tanning bed usage than other groups of students and that regardless of sorority status, the most important motivating factor will be the intent to enhance one's appearance. Methods: Undergraduate students at 2 state-funded universities were recruited for participation in this institutional review board-exempt survey via distribution to e-mail addresses and social media accounts affiliated with student organizations/clubs. Results: Among all respondents, the most common motivating factors for tanning bed use were the perception of improved self-appearance and boosted self-confidence. Female sorority members were more likely to use tanning beds and also more likely to report being motivated by enhanced appearance and self-confidence, than their female counterparts who were not sorority members. Limitations: The sample size (n = 321) and population of this study allows data to only be generalizable to surrounding states with similar demographics. The findings of this study are subject to recall bias as the data is self-reported. Conclusion: Tanning bed use remains a popular practice among young people. Understanding motivations for tanning bed use among populations at increased risk of partaking in this behavior allows for educating these groups on the risks associated with ultraviolet radiation exposure. It is crucial that providers continue to promote skin health and take steps to dissuade detrimental practices and possible habit-forming behaviors at the individual and state levels.

Chemical bonding of cross-linked glutaraldehyde/chitosan on the surface of a titanium wire to prepare a robust biocompatible SPME fiber for analysis of phytohormones in plants.

A robust biocompatible solid-phase microextraction (SPME) fiber, so-called Ti/APTS/GA/CS, was prepared by chemical bonding of cross-linked glutaraldehyde-chitosan to the surface of a titanium wire using APTS. The fiber was applied for sampling of phytohormones in plant tissues, followed by HPLC-UV analysis. The structure and morphology of the fiber coating was investigated by FT-IR, SEM, EDX, XRD, and TGA techniques. A Box-Behnken design was implemented to optimize the experimental variables. The calibration graphs were linear over a wide linear range (0.5-200 µg L-1) with LODs over the range of 0.01-0.06 µg L-1. The intra-day and inter-day precisions were found to be 1.3-6.3% and 4.3-7.3%, respectively. The matrix effect values ranged from 86.5% to 111.7%, indicating that the complex sample matrices had an insignificant effect on the determination of phytohormones. The fiber was successfully employed for the direct-immersion SPME (DI-SPME-HPLC) analysis of the phytohormones in cucumber, tomato, date palm, and calendula samples.

Adsorption properties and mechanism of Cu(II) on virgin and aged microplastics in the aquatic environment.

Microplastics (MPs) migrate by adsorbing heavy metals in aquatic environments and act as their carriers. However, the aging mechanisms of MPs in the environment and the interactions between MPs and heavy metals in aquatic environments require further study. In this study, two kinds of materials, polyamide (PA) and polylactic acid (PLA) were used as target MPs, and the effects of UV irradiation on the physical and chemical properties of the MPs and the adsorption behavior of Cu(II) were investigated. The results showed that after UV irradiation, pits, folds and pores appeared on the surface of aged MPs, the specific surface area (SSA) increased, the content of oxygen-containing functional groups increased, and the crystallinity decreased. These changes enhanced the adsorption capacity of aged MPs for Cu(II) pollutants. The adsorption behavior of the PA and PLA MPs for Cu(II) conformed to the pseudo-second-order model and Langmuir isotherm model, indicating that the monolayer chemical adsorption was dominant. The maximum amounts of aged PA and PLA reached 1.415 and 1.398 mg/g, respectively, which were 1.59 and 1.76 times of virgin MPs, respectively. The effects of pH and salinity on the adsorption of Cu(II) by the MPs were significant. Moreover, factors such as pH, salinity and dosage had significant effects on the adsorption of Cu(II) by MPs. Oxidative complexation between the oxygen-containing groups of the MPs and Cu(II) is an important adsorption mechanism. These findings reveal that the UV irradiation aging of MPs can enhance the adsorption of Cu(II) and increase their role as pollutant carriers, which is crucial for assessing the ecological risk of MPs and heavy metals coexisting in aquatic environments.

Rapid visual dual-mode detection of Zr(IV) based on L-histidine functionalized gold nanoparticles.

Heavy metal pollution has always been a great threat to human health and safety. Compared with other heavy metals, although zirconium ion (Zr(IV)) is equally harmful, due to the lack of research on Zr(IV) in the biological systems and environment, its detection does not seem to have received the attention it deserves. Herein, a rapid visual dual-mode detection (colorimetric and chrominance method) of Zr(IV) based on L-histidine functionalized gold nanoparticles (HIS-AuNPs) has been reported. AuNPs and HIS-AuNPs before and after adding Zr(IV) were characterized by UV-Vis, TEM, DLS, Zeta potential, EDS and FT-IR, etc. These results showed that L-histidine was successfully modified on the surface of AuNPs by forming a stable Au-N bond, and its modification had little effect on the dispersion degree of AuNPs. After the addition of Zr(IV), interaction of this metal ion with the imidazolyl group on L-histidine can obviously cause the aggregation of HIS-AuNPs within 12 min, and the dispersion state and particle size of HIS-AuNPs can be significantly changed. These two detection modes were established by means of absorbance and color change of solution, and being used in addition and recovery experiments of Zr(IV) in natural water. Under the optimal conditions, these two modes exhibited good linearity within 15-70 and 20-100 µmol L-1, and limit of detection of 2.62 and 6.25 µmol L-1. The proposed method was highly sensitive and selective, which provided a new convenient way to realize the detection of Zr(IV).

Antibiotic residues in pasteurised and Raw Cow's milk in Dhaka, Bangladesh.

This study aimed to investigate antibiotic residues such as oxytetracycline, ciprofloxacin, enrofloxacin and levofloxacin, in both pasteurised and raw cow's milk. A method using high-performance liquid chromatography with a UV detector (HPLC-UV) was developed and validated following International Conference on Harmonization (ICH) guidelines for simultaneous detection and quantification of these residues. The technique demonstrated linearity, with r2 values ranging from 0.999 to 1.00 within the 1.3-15.0 µg ml-1 range for each antibiotic. Thirty cow's milk samples, raw and pasteurised, from Dhaka's local markets were analysed, revealing the presence of enrofloxacin and levofloxacin, while oxytetracycline was absent in all samples. Notably, pasteurised milk samples contained enrofloxacin, levofloxacin and oxytetracycline, with groups P6 and P7 exceeding the Maximum Residue Limit for enrofloxacin, levofloxacin and ciprofloxacin (121 µg l-1). This study emphasises antibiotic residues in milk, with a validated method holding promise for routine analysis in industries requiring simultaneous quantitation of multiple antibiotics.

Validation of UV-Vis spectrophotometric and colorimetric methods to quantify methotrexate in plasma and rat skin tissue: Application to in vitro release, ex vivo and in vivo studies from dissolving microarray patch loaded pH-sensitive nanoparticle.

This research transformed MTX into smart nanoparticles that respond to the acidic conditions present in inflammation. These nanoparticles were then incorporated into a patch that dissolves over time, aiding their penetration. A method using UV-Vis spectrophotometry was validated to support the development of this new delivery system. This method was used to measure the quantity of MTX in the prepared patches in various scenarios: in laboratory solutions with pH 7.4 and pH 5.0, in skin tissue, and plasma. This validation was conducted in laboratory studies, tissue samples, and live subjects, adhering to established guidelines. The resulting calibration curve displayed a linear relationship (correlation coefficient 0.999) across these scenarios. The lowest quantity of MTX that could be accurately detected was 0.6 µg/mL in pH 7.4 solutions, 1.46 µg/mL in pH 5.0 solutions, 1.11 µg/mL in skin tissue, and 1.48 µg/mL in plasma. This validated method exhibited precision and accuracy and was not influenced by dilution effects. The method was effectively used to measure MTX levels in the developed patch in controlled lab settings and biological systems (in vitro, ex vivo, and in vivo). This showed consistent drug content in the patches, controlled release patterns over 24 h, and pharmacokinetic profiles spanning 48 h. However, additional analytical approaches were necessary for quantifying MTX in studies focused on the drug's effects on the body's functions.

Spectroscopic Analysis of the Bacterially Expressed Head Domain of Rotavirus VP6.

The rotavirus capsid protein VP6 forms the middle of three protein layers and is responsible for many critical steps in the viral life cycle. VP6 as a structural protein can be used in various applications including as a subunit vaccine component. The head domain of VP6 (VP6H) contains key sequences that allow the protein to trimerize and that represent epitopes that are recognized by human antibodies in the viral particle. The domain is rich in beta-sheet secondary structures. Here VP6H was solubilised from bacterial inclusion bodies and purified using a single affinity chromatography step. Spectral (far-UV circular dichroism and intrinsic tryptophan fluorescence) analysis revealed that the purified domain had native-like secondary and tertiary structures. The domain could maintain structure up to 44°C during thermal denaturation following which structural changes result in an intermediate forming and finally irreversible aggregation and denaturation. The chemical denaturation with urea and guanidinium chloride produces intermediates that represent a loss in the cooperativity. The VP6H domainis stable and can fold to produce its native structure in the absence of the VP6 base domain but cannot be defined as an independent folding unit.

Innovative textiles treated with TiO2-AgNPs with succinic acid as a cross-linking agent for medical uses.

Silver and titanium-silver nanoparticles have unique properties that make the textile industry progress through the high quality of textiles. Preparation of AgNPs and TiO2-Ag core-shell nanoparticles in different concentrations (0.01% and 0.1% OWF) and applying it to cotton fabrics (Giza 88 and Giza 94) by using succinic acid 5%/SHP as a cross-linking agent. Ultra-violet visible spectroscopy (UV-Vis), X-ray diffraction (XRD), dynamic light scattering (DLS), zeta potential, transmission electron microscopy (TEM), scanning electron microscopy/energy-dispersive X-ray (SEM-EDX) are tools for AgNPs and TiO2-AgNPs characterization and the treated cotton. The resulting AgNPs and TiO2-AgNPs were added to cotton fabrics at different concentrations. The antimicrobial activities, UV protection, self-cleaning, and the treated fabrics' mechanical characteristics were investigated. Silver nanoparticles and titanium dioxide-silver nanoparticles core-shell were prepared to be used in the treatment of cotton fabrics to improve their UV protection properties, self-cleaning, elongation and strength, as well as the antimicrobial activities to use the produced textiles for medical and laboratory uses and to increase protection for medical workers taking into account the spread of infection. The results demonstrated that a suitable distribution of prepared AgNPs supported the spherical form. Additionally, AgNPs and TiO2-AgNPs have both achieved stability, with values of (- 20.8 mV and - 30 mV, respectively). The synthesized nanoparticles spread and penetrated textiles' surfaces with efficiency. The findings demonstrated the superior UV protection value (UPF 50+) and self-cleaning capabilities of AgNPs and TiO2-AgNPs. In the treatment with 0.01% AgNPs and TiO2-AgNPs, the tensile strength dropped, but the mechanical characteristics were enhanced by raising the concentration to 0.1%. The results of this investigation demonstrated that the cotton fabric treated with TiO2-AgNPs exhibited superior general characteristics when compared to the sample treated only with AgNPs.

Engineered Nanocomposite Coatings: From Water-Soluble Polymer to Advanced Hydrophobic Performances.

In this work, a water-soluble (hydrophilic) polymer was used to form a hydrophobic coating on silicon substrates (Si) in a two-step process comprising (i) the transformation of the polymer into an insoluble material and (ii) the structuring of this coating at nanometric and micrometric scales to achieve the desired hydrophobic behavior. Polyvinylpyrrolidone (PVP), a water-soluble commodity polymer, was crosslinked using benzophenone and UV irradiation to produce a water-insoluble PVP coating. The nanometric scale roughness of the coating was achieved by the addition of silica nanoparticles (NPs) in the coating. The micrometric scale roughness was achieved by forming vertical pillars of PVP/NP coating. To prepare these pillars, a perforated polystyrene (PS) template was filled with a PVP/NP suspension. Micrometer scale vertical pillars of PVP/silica NPs were produced by this method, which allowed us to tune the wettability of the surface, by combining the micrometric scale roughness of the pillars to the nanometric scale roughness provided by the nanoparticles at the surface. By adjusting the various experimental parameters, a hydrophobic PVP coating was prepared with a water contact angle of 110°, resulting in an improvement of more than 80% compared to the bare flat film with an equal amount of nanoparticles. This study paves the way for the development of a more simplified experimental approach, relying on a blend of polymers containing PVP and NPs, to form the micro/nano-structured PVP pillars directly after the deposition step and the selective etching of the sacrificial major phase.

Green- and Blue-Emitting Tb3+-Activated Linde Type A Zeolite-Derived Boro-Aluminosilicate Glass for Deep UV Detection/Imaging.

Tb3+-activated LTA zeolite-derived boro-aluminosilicate glass samples with a composition of xTb2O3-68(Na2O-Al2O3-SiO2)-32B2O3 (x = 0.2, 1.0 and 10 extra wt%) were prepared using the melt-quenching method. The emission spectra recorded upon ultraviolet (UV) excitation with two different wavelengths of 193 and 378 nm showed blue light (5D3 to 7FJ=6,5,4 and 5D4 to 7F6 transitions of Tb3+) and green light (5D4 to 7F5 transition of Tb3+) emissions with comparable intensities up to a Tb3+ concentration of 10 extra wt%. Of note, the mean decay times of the green luminescence of the glass samples were relatively fast (<20 µs). The synthesized glass has potential in applications concerning UV imaging, UV detection, and plasma display panels.

Study on the Influence of UV Light on Selective Antibacterial Activity of Silver Nanoparticle Synthesized Utilizing Protein/Polypeptide-Rich Aqueous Extract from The Common Walkingstick, Diapheromera femorata.

Common walkingstick (Diapheromera femorata) aqueous extract (CWSAE) can induce the synthesis of useful bionanomaterials. CWSAE is rich in water-soluble organic compounds such as proteins and polypeptides that function as reducing/stabilizing agents for nanoparticle formation from Ag+ ion precursors. The synthesized AgNPs exhibited a moderately uniform size, with the majority falling within the range of 20-80 nm. These AgNPs were UV-treated and tested as antibacterial agents to inhibit the growth of four pathogenic bacteria (Burkholderia cenocepacia K-56, Klebsiella pneumoniae ST258, Pseudomonas aeruginosa PAO1, and Staphylococcus aureus USA300), as well as one common bacterium (Escherichia coli BW25113). The disk diffusion test demonstrated that the UV-treated AgNPs significantly and selectively inhibited the growth of Staphylococcus aureus USA300 and P. aeruginosa, while showing a small effect on the other two species. This suggests the potential application of green-chemically synthesized AgNPs as selective antibacterial agents. Furthermore, we studied the effects of short-term (1-2 min) and long-term (5-30 min) UV treatment on the selective cytotoxicity of the AgNPs and found that the cytotoxicity of the AgNPs could depend on the duration of UV exposure against certain bacteria.

Application of bi-directional long short-term memory in separating NO and SO2 ultraviolet differential absorption spectrum signals.

To safeguard the environment, it is crucial to monitor the emissions of nitrogen oxide (NO) and sulfur dioxide (SO2), harmful pollutants generated during fossil fuel combustion in industries. However, accurately measuring ultra-low concentrations of SO2 and NO remains a challenge. In this study, we developed an optical measurement system based on ultraviolet differential optical absorption spectroscopy (UV-DOAS) to address this issue. The 200-230 nm cross-sensitivity band was chosen for SO2 and NO. Experimental data with a mixed gas concentration range of 1-25 ppm for SO2 and NO was utilized. We proposed a fast algorithm based on Bi-directional Long Short-Term Memory (Bi-LSTM) to extract the differential optical density, overcoming the mutual interference between SO2 and NO. A nonlinear calibration model was employed to invert the separated differential absorption spectra and determine the gas concentrations. The results demonstrated a detection limit (DL) of 0.27 ppm and a full-scale error of 3.15 % for SO2, while for NO, the DL was 0.32 ppm and the full-scale error was 2.81 %. The uncertainties in SO2 and NO detection were calculated as 1.73 % and 1.96 %, respectively.

Effects of cupric ions on the formation of chlorinated disinfection byproducts from nitrophenol compounds during UV/post-chlorination.

Cupric ions (Cu2+) are ubiquitous in surface waters and can influence disinfection byproducts (DBPs) formation in water disinfection processes. This work explored the effects of Cu2+ on chlorinated DBPs (Cl-DBPs) formation from six representative nitrophenol compounds (NCs) during UV irradiation followed by a subsequent chlorination (i.e., UV/post-chlorination), and the results showed Cu2+ enhanced chlorinated halonitromethane (Cl-HNMs) formation from five NCs (besides 2-methyl-3-nitrophenol) and dichloroacetonitrile (DCAN) and trichloromethane (TCM) formation from six NCs. Nevertheless, excessive Cu2+ might reduce Cl-DBPs formation. Increasing UV fluences displayed different influences on total Cl-DBPs formation from different NCs, and increasing chlorine dosages and NCs concentrations enhanced that. Moreover, a relatively low pH (5.8) or high pH (7.8) might control the yields of total Cl-DBPs produced from different NCs. Notably, Cu2+ enhanced Cl-DBPs formation from NCs during UV/post-chlorination mainly through the catalytic effect on nitro-benzoquinone production and the conversion of Cl-DBPs from nitro-benzoquinone. Additionally, Cu2+ could increase the toxicity of total Cl-DBPs produced from five NCs besides 2-methyl-3-nitrophenol. Finally, the impacts of Cu2+ on Cl-DBPs formation and toxicity in real waters were quite different from those in simulated waters. This study is conducive to further understanding how Cu2+ affected Cl-DBPs formation and toxicity in chlorine disinfection processes and controlling Cl-DBPs formation in copper containing water.

Exceptional Stability against Water, UV Light, and Heat for CsPbBr3@Pb-MOF Composites.

All-inorganic lead halide perovskite nanocrystals (NCs) have been widely applied in optoelectronic devices owing to their excellent photoluminescence (PL) properties. However, poor stability upon exposure to water, UV light or heat strongly limits their practical application. Herein, CsPbBr3@Pb-MOF composites with exceptional stability against water, UV light, and heat are synthesized by ultrasonic processing the precursors of lead-based MOF (Pb-MOF), oleylammonium bromide (OAmBr) and cesium oleate (Cs-OA) solutions at room temperature. Pb-MOF can not only provide the lead source for the in situ growth of CsPbBr3 NCs, but also the protective layer of perovskites NCs. The formed CsPbBr3@Pb-MOF composites show a considerable PL quantum yield (PLQY) of 67.8%, and can maintain 90% of the initial PL intensity when immersed in water for 2 months. In addition, the outstanding PL stability against UV light and heat is demonstrated with CsPbBr3 NCs synthesized by the conventional method as a comparison. Finally, a green (light-emitting diode) LED is fabricated using green-emitting CsPbBr3@Pb-MOF composites and exhibits excellent stability without packaging when immersed in water for 30 days. This study provides a practical approach to improve the stability in aqueous phase, which may pave the way for future applications for various optoelectronic devices.

[Spectral Characteristics and Sources of Dissolved Organic Matter in Inflow Rivers of Baiyangdian Lake Water in Summer Flood Season].

DOM is the largest reservoir of organic carbon in the world, and it plays a crucial role in the biogeochemical cycles of natural water bodies. A river is a transition area connecting source water and receiving water that controls the DOM exchange between them. Therefore, in this study, ultraviolet visible spectroscopy (UV-vis) and three-dimensional fluorescence spectroscopy (EEMs) combined with parallel factor analysis (PARAFAC) were used to analyze the spectral characteristics and sources of dissolved organic matter in the Fuhe River, Xiaobai River, Baigouyin River, and Puhe River of Baiyangdian. The results showed that a245 and a355 in the Fuhe River and Xiaobai River were significantly higher than those in the Baigouyin River and Puhe River. E2/E3 showed that the DOM relative molecular mass of the inflow river water body was Puhe River > Baigouyin River > Fuhe River > Xiaobai River. Three components, tyrosine-like (C1), terrigenous humus (C2), and tryptophan-like (C3), were determined using three-dimensional fluorescence through PARAFAC. There was no difference among the fluorescence components (P>0.05), but there were differences among the C2 and C3 components (P<0.05). The proportion of easily degradable protein-like components (C1+C3) was higher than that of humus-like components (C2). The autogeny index BIX was greater than 1, and the humification index HIX was less than 4, indicating that the autogeny characteristics of the river bodies were obvious, and the humification degree was weak. The FI index was the highest (1.96±0.25), and the HIX index was the lowest (0.46±0.08), and the self-generated source characteristics gradually strengthened along the direction of the river entering the lake, indicating that the water body of the Fuhe River showed higher endogenous and autogenic characteristics. Based on the correlation analysis of fluorescence components and characteristic parameters of DOM, the correlations between the Fuhe River and Xiaobaihe River and between the Baigouyin River and Puhe River bodies were similar. The correlation between fluorescence components of DOM and water quality parameters of each lake was significantly different, and it was strongly correlated with nitrogen and phosphorus in water. According to multiple linear regression analysis, there was no significant difference among C1 components, but there was a significant difference between C2 and C3 components. In summary, the carbon cycle process of Baiyangdian Lake was further understood through the study on the DOM spectral characteristics and sources of the inflow river waters in the summer flood season.

Metastatic cutaneous squamous cell carcinoma accounts for nearly all squamous cell carcinomas of the parotid gland.

Primary squamous cell carcinoma of the parotid gland (pSCCP) has long been recognized as a separate entity and is included in the WHO classifications of salivary gland tumors. However, it is widely accepted among head and neck pathologists that pSCCP is exceptionally rare. Yet, there are many publications describing series of pSCCP and data from SEER and other cancer register databases indicate erroneously an increasing incidence of pSCCP. Importantly, pSCCP and metastatic (secondary) squamous cell carcinoma to the parotid gland (mSCCP) have nearly identical histological features, and the diagnosis of pSCCP should only be made after the exclusion of mSCCP. Moreover, all of the histological diagnostic criteria proposed to be in favor of pSCCP (such as, for example, dysplasia of ductal epithelium) can be encountered in unequivocal mSCCP, thereby representing secondary growth along preexistent ducts. Squamous cell differentiation has also been reported in rare genetically defined primary parotid carcinomas, either as unequivocal histological squamous features (e.g., NUT carcinoma, mucoepidermoid carcinoma), by immunohistochemistry (e.g., in NUT carcinoma, adamantinoma-like Ewing sarcoma, basal-type salivary duct carcinoma, mucoepidermoid carcinoma), or a combination of both. Another major issue in this context is that the International Classification of Diseases (ICD) coding system does not distinguish between primary or metastatic disease, resulting in a large number of patients with mSCCP being misclassified as pSCCP. Immunohistochemistry and new molecular biomarkers have significantly improved the accuracy of the diagnosis of many salivary gland neoplasms, but until recently there were no biomarkers that can accurately distinguish between mSCCP and pSCCP. However, recent genomic profiling studies have unequivocally demonstrated that almost all SCCP analyzed to date have an ultraviolet light (UV)-induced mutational signature typical of mSCCP of skin origin. Thus, mutational signature analysis can be a very useful tool in determining the cutaneous origin of these tumors. Additional molecular studies may shed new light on this old diagnostic and clinical problem. This review presents a critical view of head and neck experts on this topic.